歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-常見問題

常見問題

cnc高壓清洗機安全操作規程

作者：創始人來源：http://www.lsxrst.com/時間：2024-08-15

高壓清洗機的安全操作規程是確保操作人員和設備安全的重要指導。以下是基于多個來源整理的安全操作規程，供您參考：

The safety operating procedures for high-pressure cleaning machines are important guidance for ensuring the safety of operators and equipment. The following are safety operating procedures compiled from multiple sources for your reference:

一、操作前準備

1、 Preparation before operation

穿戴防護用品：操作前必需穿戴好勞動防護用品，包括護目鏡、防護服、手套等，以防止清洗液或高壓水濺到身體造成傷害。

Wear protective equipment: Before operation, it is necessary to wear labor protection equipment, including goggles, protective clothing, gloves, etc., to prevent cleaning fluid or high-pressure water from splashing onto the body and causing injury.

檢查設備：

Check equipment:

檢查CNC高壓清洗機的各部件是否完好無損，包括電源線、噴槍、高壓軟管等。

Check if all components of the CNC high-pressure cleaning machine are intact and undamaged, including power cords, spray guns, high-pressure hoses, etc.

確保主機、水泵等零部件齊全，并處于良好工作狀態。

Ensure that the host, water pump, and other components are complete and in good working condition.

檢查電源插頭、電源線、漏電保護裝置等是否完好，如有損壞應立即停止使用并報修。

Check if the power plug, power cord, leakage protection device, etc. are intact. If damaged, stop using immediately and report for repair.

安裝與調試：

Installation and Debugging:

清洗機應安裝在干燥、通風、避雨、避開陽光直射的地方，地面應平整且清洗機應加以固定。

The cleaning machine should be installed in a dry, ventilated, sheltered place from direct sunlight. The ground should be flat and the cleaning machine should be fixed.

打開機器上蓋，注入清潔機油至規定刻線，并檢查三角皮帶松緊程度，如不合適應調整。

Open the machine cover, inject clean engine oil to the specified mark, and check the tightness of the V-belt. If it does not meet the requirements, adjust it accordingly.

將進水管螺母內墊上密封膠墊，擰緊在機器進水口上，并確保濾網頭放入清潔水中。

Insert a sealing gasket into the nut of the inlet pipe, tighten it onto the machine inlet, and ensure that the filter head is placed in clean water.

接上高壓軟管及噴槍，并確保結合處有密封墊，用扳手?jǐn)Q緊螺母。

Connect the high-pressure hose and spray gun, and ensure that there is a sealing gasket at the joint. Use a wrench to tighten the nut.

二、操作過程

2、 Operation process

啟動設備：

Start device:

將調壓輪旋松，插上電源插頭。

Loosen the pressure regulating wheel and plug in the power plug.

打開噴槍，按動開關按鈕，按下引水閥桿排除進水管及泵內空氣。

Turn on the spray gun, press the switch button, and press the intake valve stem to remove air from the inlet pipe and pump.

待噴槍出水后，調節輸出壓力至合適程度。注意，如電壓偏低應降低輸出壓力以減輕電動機負荷。

After the water from the spray gun is discharged, adjust the output pressure to an appropriate level. Note that if the voltage is too low, the output pressure should be reduced to alleviate the load on the motor.

安全操作：

Safe operation:

嚴禁將清洗噴槍指向人、動物、電器設備、精密機械及高壓清洗機本體，以防止高壓水或清洗液造成傷害。

It is strictly prohibited to point the cleaning gun at people, animals, electrical equipment, precision machinery, and high-pressure cleaning machine bodies to prevent injury caused by high-pressure water or cleaning solution.

嚴禁使用高壓清洗機進行與工作內容無關的操作，如沖洗衣物、鞋、交通工具等。

It is strictly prohibited to use high-pressure cleaning machines for operations unrelated to the job, such as washing clothes, shoes, transportation, etc.

清洗時雙手必須緊握高壓清洗槍，防止高壓反沖力導致清洗噴槍脫手或失控。

When cleaning, both hands must tightly grip the high-pressure cleaning gun to prevent the high-pressure recoil force from causing the cleaning gun to slip or lose control.

嚴禁在高壓清洗機工作時移動設備，移動時必須在主電源斷電后或控制面板主開關切換到“?！钡奈恢煤筮M(jìn)行。

It is strictly prohibited to move the equipment while the high-pressure cleaning machine is working. When moving, it must be done after the main power is cut off or the main switch on the control panel is switched to the "stop" position.

使用時必須確保地面干燥、平坦，防止設備翻倒或漏電傷人。

When using, it is necessary to ensure that the ground is dry and flat to prevent equipment from tipping over or electric leakage causing injury.

監控設備：

Monitoring equipment:

在清洗過程中，應隨時觀察機器運轉情況，如有異常聲音、振動或溫度升高等情況應立即停機檢查。

During the cleaning process, the operation of the machine should be observed at all times. If there are any abnormal sounds, vibrations, or temperature increases, the machine should be stopped immediately for inspection.

定期檢查水管管路是否暢通無堵塞，防止外力碰撞或輾壓高壓膠管。

Regularly check whether the water pipes are unobstructed and not blocked, to prevent external collision or rolling of high-pressure rubber hoses.

三、操作后處理

3、 Post operation processing

停機操作：

Shutdown operation:

清洗完成后，應先卸壓再關閉電源和水源。

After cleaning, the pressure should be relieved before turning off the power and water sources.

扣動清洗噴槍扣機清空余水，并將高壓清洗管盤起收好，避免折彎。

Clean the spray gun and press the machine to empty the remaining water, and collect the high-pressure cleaning tube disc to avoid bending.

清潔與維護：

Cleaning and maintenance:

清洗機的清潔及維護工作必須在設備完全冷卻并且斷開主電源后進行。

The cleaning and maintenance work of the cleaning machine must be carried out after the equipment has completely cooled down and the main power supply has been disconnected.

定期檢查電源插頭、電源線、漏電保護裝置等部件的完好性，如有損壞應及時更換或維修。

Regularly check the integrity of components such as power plugs, power cords, and leakage protection devices. If there is any damage, they should be replaced or repaired in a timely manner.

定期檢查潤滑油、接地裝置、三角皮帶等部件的狀態，確保設備處于良好工作狀態。

Regularly check the condition of lubricating oil, grounding devices, V-belts, and other components to ensure that the equipment is in good working condition.

四、其他注意事項

4、 Other precautions

培訓與教育：操作人員應接受專業培訓，熟悉設備性能和操作規程，確保能夠正確、安全地操作設備。

Training and Education: Operators should receive professional training, familiarize themselves with equipment performance and operating procedures, and ensure that they can operate equipment correctly and safely.

應急預案：制定應急預案以應對可能發生的緊急情況，如設備故障、人員受傷等，確保能夠及時有效地進行處理。

Emergency plan: Develop emergency plans to respond to possible emergencies such as equipment failures, personnel injuries, etc., to ensure timely and effective handling.

記錄與報告：每次使用后應填寫設備使用記錄表，記錄設備的運行情況和維護保養情況，以便后續跟蹤和管理。

Record and report: After each use, an equipment usage record form should be filled out to record the operation and maintenance of the equipment for subsequent tracking and management.

通過以上安全操作規程的遵守和執行，可以確保CNC高壓清洗機的安全使用，延長設備的使用壽命，并降低安全事故的發生風險。

By following and implementing the above safety operating procedures, the safe use of CNC high-pressure cleaning machines can be ensured, the service life of the equipment can be extended, and the risk of safety accidents can be reduced.

本文由CNC高壓清洗機友情奉獻.更多有關的知識請點擊:http://www.lsxrst.com 真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is a friendly contribution from CNC high-pressure cleaning machine. For more related knowledge, please click: http://www.lsxrst.com Sincere attitude. We provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Please stay tuned

上一篇：通過式噴淋清洗機使用介紹
下一篇：全自動超聲波清洗機：工業清洗帶來的意義是什么？